Scaling Voronoi with Attractor Point

Replies to This Discussion

Permalink Reply by Zdenko on June 7, 2012 at 3:22pm

Hi Zaghloul4d

Tnx for definition... I am playing with it  last 24 h......just started with GH.....is there any way to do the same effect with attractor curve?? or is there possibility to create uniform panel that I can put beside each other to create line of panels. I tried to import points from my seamless voronoi panel in to your definition but no success...any help or link? Kind Regards

zdenko

Permalink Reply by jes on May 23, 2017 at 12:46pm

Hi Zaghloul4d, 

there is  a chance that this method could work for the 3d Voronoi without scaling the voids as well

Attachments:

• VORONOI WALL PATTERN.gh, 46 KB

Permalink Reply by barrubba on October 18, 2017 at 2:20am

hi,

i'm a newbie with GH and i need help..

i need to model the same attractor effect for the voronoi panel in the attached photo.

i'm downloaded your gh file and tryed to edit.. but i've some trouble..

i've created a new rectangule 300cm x 100cm, created a spline for point path, but i've no hole..

And then how can i reduce voronoi pattern dimension? (like attached photos?)

thank you

Attachments:

• voroi panel.jpg, 83 KB
• OK_voro2dGenerativeSystem.gh, 20 KB

Permalink Reply by David on June 9, 2012 at 11:59am

Again, great definition! I have the definition working below but I'm trying to remove the surfaces that are outside of the circular area. I have an "Inside" component setup which checks the center points of the surfaces inside of a closed cylinder. Can't seem to remove the surfaces though so I'm not sure what I'm missing. Attached definition and rhino base file. Any Ideas?

Attachments:

• combo_2.3dm, 51 KB
• combo_cull.gh, 10 KB

Permalink Reply by David on June 17, 2012 at 3:01pm

Also, any idea on how to add multiple attractor points?

Permalink Reply by Nikola Kungulovski on September 13, 2012 at 8:52am

I was wandering also how can it be done with an attractor curve?

Permalink Reply by Michael Pryor on September 13, 2012 at 9:01am

instead of boxes here use voronoi cells. http://formularch.blogspot.com/2012/04/gh-line-attract-repel.html

Permalink Reply by RWNB on September 13, 2012 at 9:08am

maybe this is what for you!

Attachments:

• Voronoi_2D_WithCurveAsPathsystem_01.3dm, 50 KB
• Voronoi_2D_WithCurveAsPathsystem_01.ghx, 474 KB

Permalink Reply by Nikola Kungulovski on September 13, 2012 at 9:39am

wow thanks guys for the fast answers, but i think the last script is not working properly or maybe i don't know how to set it right :)

Permalink Reply by RWNB on September 13, 2012 at 9:59am

you have to make visible the surface layer in rhino, than set to the Geo. Comp. (at the beginn) to the surface. than it must go.

Permalink Reply by Michael Pryor on September 13, 2012 at 11:01am

Here is a version I made, I went a little further having fun and added height and smoothing. Also its reversible via filter switch.

Attachments:

• Voronoi Curve+.gh, 16 KB
• Voronoi Curve+.3dm, 702 KB

Permalink Reply by RWNB on September 13, 2012 at 11:09am

LIKE!

• ‹ Previous
• 1
• 2
• 3
• 4
• Next ›
• Page