HELP No .eio file error

Replies to This Discussion

Permalink Reply by Abraham Yezioro on May 21, 2015 at 3:06pm

Hi Nita,

Can't reproduce the error. It runs fine in my system (even though there are plenty of severe errors).

It is not becouse of the materials.

Check the panel connected to the report output item from the HB_runEnergySimulation. Probably you can get from there some clues what is going on.

-A.

Permalink Reply by Nitë on May 21, 2015 at 3:24pm

Hi Abraham,

thanks for taking your time to reply.The message from the HB_runEnergySimulation is the one i copied above.I know there are materials missing and some other things to complede the definition.What other error did you detect?

Could the problem be with my computer?I re-installed energy plus...

thanks,

N

Permalink Reply by Abraham Yezioro on May 22, 2015 at 8:20am

Hard to say. But you can see the last line in the report above:

Done! Read below for errors and warnings:

So you have to check below this line and see what is bothering E+ for not running.

I usually don't blame the computer (unless the results are bad for me :-)). Also the E+ installation. Something is missing in your idf. You can check at the location where the idf is created for an ERR file. It has the same info as in the report, but that one you can upload here.

-A.

Permalink Reply by Nitë on May 23, 2015 at 9:53am

Hi Abraham,
there is no text at the panel after / Done! Read below for errors and warnings:
Blaming the computer I meant something wrong with installation of software :D

At the working directory there are no ERR, .csv or .eio files.Only the ones attached here

Thanks,

N

Attachments:

• Basecase.idf, 61 KB
• Basecase.bat, 1 KB

Permalink Reply by Abraham Yezioro on May 23, 2015 at 9:28pm

Well,

The idf file runs fine in my computer. I'm sure that if you run it manually in yours it will run too. No reason why not. Also sure the E+ is well installed.

When i see the BAT file i only can suppose that there are issues with the path. Just for the sake of this, can you change the path of this file in GH? Maybe use default values (No working directory defined). Maybe in the computer you are using there is no E disk?

-A.

Permalink Reply by Nitë on May 24, 2015 at 3:33am

Hi Abraham,

There is an E disk in my laptop.I ran it with no working directory and changed the name of the idf file, still same error.

Also opened the idf with energy plus.It shows the errors as in the pictures attached.Meanwhile I have EP 8.3 installed...

 

Thanks,

N

Attachments:

• ep.JPG, 66 KB

Permalink Reply by Nitë on May 24, 2015 at 3:40am

UPDATE:

I have results! apparently I had to open the idf with eplus and simulate, in order to create the .eio file! do I have to do this procedure everytime now?

Thanks Abraham for you time and patience.

Permalink Reply by Abraham Yezioro on May 24, 2015 at 3:51am

From your picture i see that the simulation was performed fine. But from what you wrote it doesn't (but just manually).

You are not supposedly to run manually anyways.

You need E+ 8.1 (!!). See the bat file you attached previously and you'll see that the bat is looking for the 8.1 directory. HB is not yet supporting 8.3 (Chris or Mostapha correct me if i'm wrong). I myself have both versions installed.

-A.

Permalink Reply by Nitë on May 24, 2015 at 4:11am

Aha.I was not aware that it works only with 8.1.Or may I knew that and forgot..Will install 8.1. and see what happens.

This is the report: it has 4 warnings 49 severe errors :(

Analysis period is from 1 JUN to 31 DEC
Between hours 1:00 to 24:00
Current document units is in Meters
Conversion to Meters will be applied = 1.000
[1 of 7] Writing simulation parameters...
Ground temperature data contains monthly average temperatures at 3 different depths .5 meters (1st)2 meters (2nd)4meters (3rd)respectively
[2 of 6] No context surfaces...
[3 of 6] Writing geometry...
[4 of 6] Writing materials and constructions...
[5 of 7] Writing schedules...
[6 of 7] Writing loads and ideal air system...
[7 of 7] Writing outputs...
...
... idf file is successfully written to : c:\ladybug\unnamed\EnergyPlus\unnamed.idf

Analysis is running!...
c:\ladybug\unnamed\EnergyPlus\eplusout.csv
...
...

Done! Read below for errors and warnings:

Program Version,EnergyPlus, Version 8.3.0-6d97d074ea, YMD=2015.05.24 11:32,IDD_Version 8.3.0

** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.

** Warning ** Version: in IDF="'8.1.0'" not the same as expected="8.3"

************* Beginning Zone Sizing Calculations

** Severe ** GetSurfaceData: Some Outward Facing angles of subsurfaces differ significantly from base surface.

** ~~~ ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual surfaces.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 1 of back surface=AW0 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 2 of back surface=AW0 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 3 of back surface=AW0 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.1101)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 4 of back surface=AW0 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.1101)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 1 of back surface=AW1 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.1101)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 2 of back surface=AW1 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 3 of back surface=AW1 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 4 of back surface=AW1 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.1101)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 1 of back surface=AW2 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 2 of back surface=AW2 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 3 of back surface=AW2 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 4 of back surface=AW2 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 1 of back surface=AW3 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 2 of back surface=AW3 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 3 of back surface=EW1 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 4 of back surface=EW1 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 1 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=0.9038)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 2 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=0.9038)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 3 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=16.0967)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 4 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=16.0967)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 6 of back surface=FLOOR is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 7 of back surface=FLOOR is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 8 of back surface=FLOOR is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.1101)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 9 of back surface=FLOOR is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 5 of back surface=CIELING is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 6 of back surface=CIELING is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=17.1101)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 7 of back surface=CIELING is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 8 of back surface=CIELING is in front of receiving surface=EW0

** ~~~ ** (Dot Product indicator=30.0900)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 3 of back surface=AW6 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 4 of back surface=AW6 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 1 of back surface=WALLW1 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 2 of back surface=WALLW1 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 3 of back surface=WALLW1 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 4 of back surface=WALLW1 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 1 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 2 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 3 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 4 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 1 of back surface=EW0 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 4 of back surface=EW0 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 1 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=1.4709)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 2 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=1.4709)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 3 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=15.6696)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 4 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=15.6696)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 1 of back surface=FLOOR is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 2 of back surface=FLOOR is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 2 of back surface=CIELING is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Severe ** Problem in interior solar distribution calculation (CHKBKS)

** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"

** ~~~ ** because vertex 3 of back surface=CIELING is in front of receiving surface=EW1

** ~~~ ** (Dot Product indicator=17.0963)

** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

** Warning ** ManageSizing: For a plant sizing run, there must be at least 1 Sizing:Plant object input. SimulationControl Plant Sizing option ignored.

************* Testing Individual Branch Integrity

************* All Branches passed integrity testing

************* Testing Individual Supply Air Path Integrity

************* All Supply Air Paths passed integrity testing

************* Testing Individual Return Air Path Integrity

************* All Return Air Paths passed integrity testing

************* No node connection errors were found.

************* Beginning Simulation

************* Simulation Error Summary *************

** Warning ** The following Report Variables were requested but not generated

** ~~~ ** because IDF did not contain these elements or misspelled variable name -- check .rdd file

************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL COOLING ENERGY, Frequency=Hourly

************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL HEATING ENERGY, Frequency=Hourly

************* Key=*, VarName=CHILLER ELECTRIC ENERGY, Frequency=Hourly

************* Key=*, VarName=BOILER HEATING ENERGY, Frequency=Hourly

************* Key=*, VarName=FAN ELECTRIC ENERGY, Frequency=Hourly

************* Key=*, VarName=ZONE VENTILATION FAN ELECTRIC ENERGY, Frequency=Hourly

************* Key=*, VarName=ZONE VENTILATION TOTAL HEAT LOSS ENERGY, Frequency=Hourly

************* Key=*, VarName=ZONE VENTILATION TOTAL HEAT GAIN ENERGY, Frequency=Hourly

************* There are 1 unused schedules in input.

************* There are 1 unused week schedules in input.

************* There are 3 unused day schedules in input.

************* Use Output:Diagnostics,DisplayUnusedSchedules; to see them.

************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.

************* EnergyPlus Sizing Error Summary. During Sizing: 1 Warning; 49 Severe Errors.

************* EnergyPlus Completed Successfully-- 4 Warning; 49 Severe Errors; Elapsed Time=00hr 00min 4.59sec

Thanks Abraham.I really appreciate it.

Another thing ' I posted a discussion few days ago and got no replies.And this forum is the only 'Hope' for me..Can you quickly check it?thanks.

N

http://www.grasshopper3d.com/group/ladybug/forum/topics/free-form-e...

Permalink Reply by Abraham Yezioro on May 24, 2015 at 7:52am

Most of the severe error relate to the Solar Distribution in the zone. When the zone is concave (L shape) this Distribution may give errors when set to Full Exterior and Interior" (which i think is default value). You can control this parameter with the HB_EnergySimPar -- solarDistribution_ input (probably ti FullExterior only).

Regarding the other discussion i have to say that i didn't understand well the question, so don't know what to suggest. My feeling is that MaxRad is unnecesary, but again, i may have misunderstood the question.

-A.

Permalink Reply by Chris Mackey on May 26, 2015 at 3:34pm

Abraham, Thanks for providing Nite with great support on this.

Just to confirm the question that you asked about E+ versions, the last stable release from February uses E+ 8.1 and the most up-to-date version on the github uses E+ 8.2.  We have not yet updated Honeybee to 8.3 but I think that there is a good chance we will do this before the next stable release, which I imagine should be pretty soon.

Nite, it looks like all of the errors that you are getting with the successful simulation have to do with the specifics of your geometry so the overall E+ results on the zone level should be fairly accurate but values for individual surfaces will not be.  To fix the problem, you can either accept the surface-level inaccuracies and change the solar distribution type (what Abraham suggests), you can break up all of your L-shaped surfaces into rectangular surfaces (this usually fixes everything for me), or you can break up your single zone into 3 cube-like zones with air walls between them (this always works for me).

Hope this helps,

-Chris