Grasshopper 0.8.0004 available for download

Hi All,

an incremental update is available. THIS WON'T RUN ON RHINO5 UNTIL THE NEXT R5 WIP GOES OUT!!!!

Improved Drag+Drop GUI for gh and ghx files.
Added undo recording to Curve Point Component drags.
Added Ctrl+Enter and Shift+Enter overloads for setting persistent data via parameter menus.
Slider Animations can now be aborted with Escape.
Added non-functional Manage-List GUI to the Generic parameter.
Added more smarts to the automatic cluster input/output lists.
Added Ctrl+W shortcut to Close document menu item.
Explode Tree component now uses base-zero numbering in the output.
Arc3Pt and ArcSED components now output lines if the input is co-linear.
Fixed sticky settings not being recorded when Rhino is shut down while Grasshopper is still running.
Fixed a bug with Curve -> Interval auto-casting.
Fixed tooltips showing for hidden widgets.
Fixed a bug with Cluster output parameter sorting.
Boxes would not bake if the axis intervals were reversed, this is fixed.

I'll be travelling for the next week or so, stopping at the Automatic Architecture Event in Delft.

If you need to revert to Grasshopper 0.8.0003, download the installer here.

David Rutten

david@mcneel.com

Seattle, WA

Replies to This Discussion

Permalink Reply by kleerkoat on December 12, 2010 at 12:26pm

exactly what build will this run on?

not on 12-07 i take it?

Permalink Reply by David Rutten on December 12, 2010 at 2:15pm

The very next build of Rhino5 that will go out. It is scheduled for Tuesday evening Pacific time, but we have a history of breaking the build process the day before, so it might be later.

David Rutten

david@mcneel.com

Seattle, WA

Permalink Reply by kleerkoat on December 12, 2010 at 2:29pm

thanks David!

Permalink Reply by Mårten Nettelbladt on December 12, 2010 at 2:42pm

Thanks David!

Wish: Nudge active slider with arrow keys (left/right). Shift+Arrows = bigger steps (or maybe up/down arrows?)

Permalink Reply by anas on December 12, 2010 at 5:39pm

thank you very much

can i use Grasshopper 0.8.0004 for rhino 5 64bit??

Permalink Reply by taka on December 12, 2010 at 10:40pm

Thank you!

Permalink Reply by cai jieteng on December 13, 2010 at 2:40am

Thank you very much!

Permalink Reply by Dre.J on December 14, 2010 at 6:57am

thank you for your work

Permalink Reply by Alpha222 on December 14, 2010 at 8:51am

Hi David,

I think there is a bug with the Rotate component . I intend to rotate a surface with two angle 0 and pi , I graft the angle input to get two branches, 0.8.0003 would do this job perfectly while 0.8.0004 failed .see below .

Permalink Reply by Astro/Naught on December 14, 2010 at 9:55am

Hi David,

Just watched the 'Introduction to Grasshopper' on the Wibinear. Great stuff. I wanted to ask if you could share the 'ShowCase' ghx definition file, which you started off with. That would be great. Thanks and keep up the good work.

Permalink Reply by Thomas Bildsøe on December 15, 2010 at 2:31am

Hi David

Thanks for the new build. I'm seeing some flickering in the top left corner of the interface when resizing, no big problem. Am I the only one seing it? I haven't detected it before 08.0004.

Permalink Reply by Danny Boyes on December 15, 2010 at 11:17am

Hi David,

There's a small bug in the Tree Explode Component. When you first put the component onto the canvas the numbering is 1 and 2 but if you go to the output manager and don't do anything the numbering changes to 0 and 1.

Danny