Drawing flat Rectangle Surface from Angled surface's highest edge

Replies to This Discussion

Permalink Reply by Chris Tietjen on October 26, 2012 at 9:51pm

Here's a definition that gives the rafter you want.  I'm not very adept at resolving path issues so it will only display one rafter at a time depending on what values you use in the the list item component (0,1;2,3 or 4,5). 

Chris

Attachments:

• 9_RafterProblem.3dm, 42 KB
• 9_RafterProblem.gh, 21 KB

Permalink Reply by Otto Pile on October 27, 2012 at 4:00am

Hello, Chris.

Thank you for your approach!

Unfortunately, there are some major issues, which it doesn't suit:

1. In your approach surface before extruding is being drawn from the mid curve/line, which is being offset to both sides and these side curves are making the upper surface. In this case it's not working, because I wouldn't be possible to produce/ cut such a beam (reason why mentioned in second point). I need to make surface from highest curve/line, like in drawings before.

2. In your approach surface is being extruded on Z axis, which also gives me different beam thickness than I would need.

Imagine, I have wooden beams and I wand to make frame for pyramid from them. To do less wood cutting I would just align beam in needed angle so the bottom surface would be parallel to ground. So, because of wood is being aligned - wood thickness is equal the distance between upper surface and surface offseted normal to upper surface. If I am extruding upper surface on z direction -  I am getting beams cross cut height not the beams thickness, because beams is aligned. 

From this point it is clear that I have to do surface offset from highest curve/line not the mid line, because after cutting top surface on angle, there just wont be enough "wood" for part of beams  up from top/ base surface's middle curve/line (see image attached)

Do you have any other idea? Maybe you know how it would be possible to align bounding box to each of these surfaces (It would be the most easy way to do that)?

Permalink Reply by Chris Tietjen on October 27, 2012 at 5:49am

Trythis.

Attachments:

• 9_RafterProblem_2.gh, 28 KB

Permalink Reply by Chris Tietjen on October 27, 2012 at 6:22am

Rafter_Problem

The link above is for a screencast.

Chris

Permalink Reply by Otto Pile on October 27, 2012 at 6:49am

Chris, thanks!

This is what I was looking for.

Only one more thing:

Do you have any idea, how I could pick a "highest" curve projected onto roof surface and a highest curve's centroid surface not by typing integer on "item" component, but by picking the one which higher from ground? This is important, because I have pyramids with different low-high direction, so the same integer won't work for all.

Permalink Reply by Chris Tietjen on October 27, 2012 at 5:46pm

This should sort out the proper lines and faces but you'll have to test it on your geometry to be sure.

Chris

Attachments:

• 9_RafterProblem_2.gh, 32 KB

Permalink Reply by Otto Pile on October 27, 2012 at 6:15pm

Chris, thanks!

I'm cleaning up my function at the moment. Will try it out asap and let you know, how it worked.

Permalink Reply by Otto Pile on October 28, 2012 at 12:35pm

Chris,

Your approach is almost working for me. Only problem - I can't find a right highest point, because from ground plane extruded pieces, from which afterwards beams are being cut off, is being extruded different directions and because of that for some highest point is on start points but for some on end points.

I am trying to sort edge curves, but this far without any luck. 

Do you have any idea how it could be made?

Permalink Reply by Chris Tietjen on October 28, 2012 at 2:29pm

Otto,

You might want to try inserting the Flip component into your definition to get all of the curves going in the same direction. 

We're about to get hit with a hurricane here so this may be my last post for a few days depending on power outages. 

Chris

Permalink Reply by Otto Pile on October 28, 2012 at 2:52pm

Chris,

I already tried that. Didn't work out. Curves remained same direction like before.

Take care! Hope to hear from you any time soon.