annual profiles doesnt math with the point groups

Hello everybody,

I have some problem with reading the hourly(and annual)result when I have dynamic shading, it writes me that I have different number of point groups as annual profiles.

And I know that point groups are regarded to mesh etc. but this is a really siply testbox 10x10x3m ,where is just one floor (mesh). (above it is the chart for shading operation)

Can anybody help me with that ?

Thanks a lot

Peter

Replies are closed for this discussion.

Replies to This Discussion

Permalink Reply by Mostapha Sadeghipour Roudsari on October 11, 2014 at 8:39pm

Hi Peter, Can you internalize the results and send me the file. Looks like a data management issue.Thanks,

- Mostapha

Permalink Reply by Peter Zaťko on October 13, 2014 at 7:27am

Hi Mostapha, there is the file, I even send you a message with the model and other files,

Thank you very much

Regards

Peter

Attachments:

testbox0610_elchrom.gh, 206 KB

Permalink Reply by Mostapha Sadeghipour Roudsari on October 18, 2014 at 11:24pm

Hi Peter, I checked your file. You are adding a single point (center of the window) to test points which makes the number of test points not to match the number of mesh faces. Moreover, points are in different branches. If you are doing this intentionally then make sure to simplify the branches. -Mostapha

Permalink Reply by Peter Zaťko on October 19, 2014 at 6:20am

Hi, Mostapha
Yes I use it as sensor point, and I always flaten it to have them in one list, so I will try to just simplify it and let you know,

Thanks
Peter

Permalink Reply by Peter Zaťko on October 27, 2014 at 9:48am

Hi Mostapha,
so I tried the simplification and it doesn´t work, than I delete that one extra point and it doesn´t work too, can you please chceck it where can be the mistake ? the data is internalized

Thanks,

Peter

Attachments:

testbox_DA.gh, 211 KB

Permalink Reply by Mostapha Sadeghipour Roudsari on November 2, 2014 at 3:03pm

Hi Peter, I'm checking your file an I can see the check fails as you have more than one shading states. Let me see if I can fix it this evening. -Mostapha

Permalink Reply by Peter Zaťko on November 11, 2014 at 9:49am

Hi Mostapha,

Any results with fixing it ?

Thank,

Peter

Permalink Reply by Mostapha Sadeghipour Roudsari on November 16, 2014 at 5:55pm

Hi Peter. Sorry that it took me so long to get this fixed. Check the attached file for a fixed version. I had to make couple of modifications in components (The ones in red group). There is still a limitation for number of shading groups for visualization which shouldn't be an issue in your case. Thanks for your patience.

-Mostapha

Attachments:

testbox0610_elchrom_msr.gh, 189 KB

Permalink Reply by Peter Zaťko on November 17, 2014 at 7:29am

Hi Mostapha,

You are amazing, it s totally fine for me now. Thank you for spending your time above it. So now the (red) components are changed on a github too or just in that file ?

Thanks again,

Peter

Permalink Reply by Mostapha Sadeghipour Roudsari on November 17, 2014 at 8:28am

Hi Peter. It is updated on github.

Permalink Reply by Abraham Yezioro on November 17, 2014 at 11:42am

Hi Mostapha,

Testing your file I've found a bug with the runDaylightAnalysis OR readAnnualResultsI components. I gave an input in the _numOfCPUs_ (4). The simulation went fine but after it finished the readAnnualResultsI component complains about an unmatched number of points (1. Number of points in ill files: 10 doesn't match the number of points in point files: 43). Running with 1 CPU is ok.

Or i'm missing something ...

Thanks,

-A.

Permalink Reply by Mostapha Sadeghipour Roudsari on November 17, 2014 at 9:48pm

Thanks Abraham. This is a sorting bug. The files end up in the wrong branch. I will take a closer look tomorrow and let you know the results.