_sweep 1 rail

Replies to This Discussion

Permalink Reply by Rémy Maurcot on December 16, 2010 at 2:25pm

After test:
VB scipt:
rhUtil.RhinoSweep1 (x, y)
X Oncurve
Y Oncurve
Error: A value of type 'RMA.OpenNURBS.OnCurve' can not be converted to 'RMA.Rhino.MArgsRhinoSweep1'. (Line 83)
Error: A value of type 'RMA.OpenNURBS.OnCurve' can not be converted to 'Table 1 dimension (s) RMA.OpenNURBS.OnBrep'. (Line 83)

Message d'origine:

Après essai:
VB Scipt:
rhUtil.RhinoSweep1(x, y)
X Oncurve
Y Oncurve
Error: Une valeur de type 'RMA.OpenNURBS.OnCurve' ne peut pas être convertie en 'RMA.Rhino.MArgsRhinoSweep1'. (line 83)
Error: Une valeur de type 'RMA.OpenNURBS.OnCurve' ne peut pas être convertie en 'Tableau à 1 dimension(s) de RMA.OpenNURBS.OnBrep'. (line 83)

Permalink Reply by Jon Mirtschin on December 17, 2010 at 12:02am

Hi Rhymone,

 

If you're coding Sweep1, perhaps this discussion will help: http://www.grasshopper3d.com/forum/topics/sweep-1-with-vbnet-node

 

 

I think StructDrawRhino should also be capable of producing the sweeps you need (if you want to save the headaches of coding the orientation of curves etc).

 

You can build up custom libraries of profiles (refer the letter 'c' and number '3'  in the above image) and I'm happy to implement any suggestions or requirements if particular improvements or alternative sweep orientations are required.

 

Feel free to contact me if you wish to discuss and I can explain further.

 

Cheers,

 

Jon

Permalink Reply by Rémy Maurcot on December 17, 2010 at 8:18am

Hello,

In your examples that are merely forms of "simple ".

My profile is not perpendicular to the curve ...

His works also?

Bonjour,

Dans vos exemples ce ne sont que des formes "simple".

Mon profil n'est pas perpendiculaire à la courbe ...

Sa marche aussi ?

 

Permalink Reply by Rémy Maurcot on December 17, 2010 at 1:04pm

I have readen this post :http://www.grasshopper3d.com/forum/topics/sweep-1-with-vbnet-node

I have used this code _sweep1.ghx but with my elements it's impossible.

You,Have you succeded with this code?

 

J'ai lu ce post: http://www.grasshopper3d.com/forum/topics/sweep-1-with-vbnet-node

Utiliser le code fournis _sweep1.ghx mais je n'arrive pas à le faire fonctionné avec mes élèments.

Marche-t-il pour vous ?

 

Permalink Reply by Jon Mirtschin on December 19, 2010 at 2:38am

Hi Rhymone,

 

The code for the scripting component I referred to worked for geometry I've used.

Can you post (or send to me) an example of a sweep rail and profile that is not working?

 

Cheers,

 

Jon

Permalink Reply by Rémy Maurcot on December 19, 2010 at 6:59am

Hi jon,

I have succeded to extrude by_sweep my profile with rail but is 2D rail.

i would like to extrude my profile according to my sweep with grasshoper,

The sweep is managed by the slope, and altitude.

So the sweep defined is a 3Dcurve !!

 

When I launch the command with  a 2Dcurve it's OK (grasshopper)

When I launch the command with  a 3Dcurve it's OK with rhino.

But with grasshopper it's not OK..

 

Thanks for your response...

PS:pointfouille.3dm & fouille.ghx

Message d'origine:

J'ai reçu à l'extruder en 2D.

J'aimerais extrudé mon profil selon mon rail qui est gérer dans grasshopper par la pente, et l'altitude de départ donc au final j'ai une courbe 3D.
Lorsque je lance la commande sur le rail 2D sa marche.
Lorsque je lance la commande sur rhino en 3D sa marche.
Mais dans grasshopper sa ne marche pas

Attachments:

• point fouille.3dm, 27 KB

Permalink Reply by Jon Mirtschin on December 20, 2010 at 1:55am

Hi Rhymone,

 

There will be a setting somewhere in the sweep code to enable it to work with non-planar rails, I haven't had a chance to investigate where and what that is, but I did quickly update my StructDrawRhino code for sweeping and it seems to be producing the result you need.  If you wish to try it, installation instructions are here: http://www.grasshopper3d.com/group/geometrygym/forum/topics/install...

 

I've attached my definition, the plugin sweep works best if you place the profile in the global YZ plane (it treats the sweep path as the x axis).

 

Hope it helps,

 

Jon

Attachments:

• fouille.gh, 124 KB

Permalink Reply by Rémy Maurcot on December 20, 2010 at 11:59am

I have a trial version of Rhino 4.
Should I wait to install the complete,for instal geometry gym?

MO:

Je n'ai qu'une version d'évaluation de rhino 4.
Dois je attendre la complète pour installer geometry gym?

Permalink Reply by Jon Mirtschin on December 20, 2010 at 1:30pm

Hi Rhymone,

 

All plugins should work with evaluation/trial version of Rhino, except after 25 saves they are disabled.  I'm not sure if you have to reinstall when you change to a purchased version, but it is not a big deal to do so.

 

Cheers,

 

Jon

Permalink Reply by Rémy Maurcot on December 20, 2010 at 2:45pm

Please re-join your ghx file fouille.ghx.

Thanks

Permalink Reply by Jon Mirtschin on December 20, 2010 at 9:48pm

Hi,

 

Did my file not open?  Make sure you have the latest version of SDR installed and run the rhino command sdrZZLicenseRequest

 

I've attached the file again in xml format.

Attachments:

• fouille jon.ghx, 722 KB